Whirlpool Dryer WED6600VW0 No heat or not enough heat

The Heating Element is an OEM replacement part for Whirlpool dryers. This part is responsible for generating the heat necessary to dry clothes efficiently. The heating element works by electrically heating a coil or a wire to a high temperature when power is applied, radiating heat throughout the dryer drum to evaporate water from the clothes.

Causes for the heating element to fail can vary but often include overloading the dryer, which restricts airflow and can cause the element to overheat and burn out. Another common cause is age; over time, the constant heating and cooling can lead to metal fatigue and eventual failure of the element. Additionally, poor ventilation and lint buildup can cause the dryer to overheat, damaging the heating element.

Symptoms of a bad heating element include:  

• Taking a long time to dry clothes or not drying completely
• No heat produced by the dryer during cycles
• Tripped circuit breaker or blown fuse after drying

Note: has 2-5/16" male terminals.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Thermal Fuse is an OEM replacement part for Whirlpool dryers. This easy-to-install thermal cut-off is designed to shut down your dryer when temperatures become too high, protecting the appliance from overheating. It's a one-time fuse, meaning it cannot be reset and needs to be replaced. It can be tested for continuity with a multimeter.

Causes of Bad Thermal Fuse

• Excessive lint buildup in the dryer vent
• Poor air flow causing overheating
• Failing to clean out the lint filter regularly
• Faulty heating element or drying cycle thermostat

Don't let a faulty dryer leave you stranded with wet clothes! Replace your dryer's Thermal Fuse to get back to using your dryer worry-free. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Thermistor is an OEM part for Whirlpool brand dryers. It is a temperature-sensing resistor that monitors air temperature changes during the drying cycle. The thermistor provides feedback to the control board on heating element performance and internal air condition. 

Symptoms of a failed thermistor include:

• Inaccurate temperature readings and selections  
• Improper or incomplete drying
• Safety issues from overheating due to lack of feedback
• Error codes displayed on the control panel

Causes can be related to normal wear and environmental exposure over time. Failure prevents the dryer from achieving optimal drying conditions.

This genuine Whirlpool thermistor replacement restores precise air temperature monitoring. It ensures the control board receives accurate input to effectively regulate heating levels. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Heating Element Connecting Wire is an OEM part for Whirlpool dryers, designed to provide a secure electrical connection to the dryer's heating element. This critical component ensures that the heating element receives the power it needs to generate heat for drying clothes. 

Causes of a bad heating element connecting wire can include overheating, physical damage, or wear and tear over time. These issues can lead to a loss of connectivity, resulting in the heating element failing to heat up. 

Symptoms of a bad Heating Element Connecting Wire include:

• The dryer not heating up despite having power
• Intermittent heating, suggesting a loose or faulty connection
• Unusual smells or signs of burning, indicating overheating or damage to the wire

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This dryer repair kit is an OEM replacement part for Whirlpool dryers.

The kit includes:

• One Dryer belt (341241)
• Drum support roller kit (349241T)
• One idler pulley (WP691366)
• Instructions.

While some parts in this kit may not fit your specific model, you can use your model number to check for the specific parts you need. This ensures that you have the right parts for your particular dryer and can make the repair process as smooth and straightforward as possible.

Includes screws and wire connectors. For the complete terminal block kit use 279320.

The OEM Replacement Part is a Blower Wheel, designed for use in specific Whirlpool Dryer models. This 8 5/8" diameter wheel, is crafted to move air through the appliance effectively, utilizing a squirrel cage design. Its main function is to blow air through the dryer drum and out the exhaust, a crucial element in the drying process.

The blower wheel attaches to the motor shaft using left-handed threads and can be removed by unscrewing it clockwise off the motor shaft. It is particularly suitable for 29-inch models with a lint filter on top. This part is compatible with select Whirlpool brand models including Kenmore, and Roper.