Whirlpool Dryer WED5840SW0 Too hot

If your Whirlpool dryer or washer/dryer combo is not functioning properly, it may be due to a damaged thermal cut-off. This thermal cut off kit is an authentic OEM replacement kit that is designed to prevent the dryer from overheating.

Made of durable metal. Both components are mounted on the heater housing. They measure approximately 2 inches long and 1.5 inches wide each. If the thermal cut-off fuse has gone out, the dryer will not function but replacing it using the components in this kit is simple.

This Kit Includes:

• High Limit Thermostat (250°F Limit)
• A Cut Off Fuse (309°F Limit)
• Female Spade Terminals
• Jumper Wires

It is important to note that a plugged lint screen, something stuck in the exhaust vent, or a broken blower wheel can cause the thermal cut-off to fail or become damaged. Don't wait to replace a faulty thermal cut-off. Order now.

Restore your dryer's safety and performance with this Hi-Limit Thermostat. The Whirlpool brand OEM replacement part is designed to prevent overheating and keep your appliance running. This 3-wire thermostat is equipped with 1/4" male, 3/16" male, and 1/4" female connectors. It has been designed to operate at a temperature rating of L221 degrees. 

The thermostat includes a terminal extension arm for easy installation. This vital component maintains proper temperature by opening at around 250 degrees Fahrenheit. Safety features such as this keep your dryer safe from potential damage.

If you suspect a thermostat malfunction causing your dryer to lose heat, first locate it. The thermostat is located beneath the dryer vent at the back of the appliance. Test the thermostat for continuity at room temperature using a multimeter. If the reading indicates a defective thermostat, replace it.  Purchase this high-quality, silver/black metal and plastic model to restore your dryer's safety.

The Heating Element is an OEM part compatible with Whirlpool brand dryers. It generates the heat needed to effectively dry clothes and linens during the drying cycle. The precise coil design allows it to heat the air inside the dryer to optimum temperatures.

Causes of a bad heating element can include normal wear and tear over time, mineral or lime buildup that impedes heat transfer, or physical damage to the coil or connecting wires.

Symptoms of a bad heating element include:  

• The dryer takes a long time to dry clothes or does not dry them completely
• Slow or inaccurate temperature selection
• Noticeable decrease in air heat output
• Tripped circuit breaker or blown fuse after drying

Note: has 2-5/16" male terminals.

Replacing the part with this genuine Whirlpool OEM heating element helps restore reliable and efficient drying performance. It is also compatible with brands such as Amana, Maytag, Jenn-Air, and KitchenAid.

The Dryer Thermostat is an OEM Replacement Part engineered to regulate the internal drying temperature of your dryer. It has a temperature limit of 155-25F and includes an internal-bias heater. This essential component might be the solution if your dryer is not heating, not starting, not drying properly, or taking too long to dry.

To ensure proper function, one should test the inner terminals on the cycling thermostat for a resistance of approximately 9K ohms. A malfunctioning thermostat that fails to shut off the heater could potentially blow the high limit. It's compatible with several brands, including Whirlpool, Maytag, Kenmore, and Crosley.

The Belt is an OEM part compatible with Whirlpool dryers. It acts as a transmission to power the drum rotation during the drying cycle. The belt reliably conveys motion from the motor to the drum, ensuring garments are properly tumble-dried. 

Symptoms of a bad belt include: 

• The drum not turning or rotating slowly 
• Excessive noise and vibration coming from the dryer
• The belt slipping off the pulley
• Discoloration, cracking, or fraying of the belt

Causes of a bad belt can be normal wear and tear over time, overloading the dryer with too many wet items, or structural damage to the belt itself. 

This genuine OEM Whirlpool part is compatible with many other brand dryers including Maytag, KitchenAid, Affresh, Roper, and some Kenmore models for dependable performance.